Vehicles
Sections
78 not categorized PORSCHE 356 B FRONT END BRACan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1987-89 (includes uncategorized and accessory items) PNA503993TU00 Originally adapted to mitigate the ordeals of off-road racing, these stylish front covers are expertly tailored to protect your Porsche from rock chips and other debris. Highest quality bras are lined with soft, flannel backing and edges are bound in felt. Hooks are rubber covered and metal tabs are doubly reinforced. License plate cutouts are provided on all models and an embossed Porsche crest is featured on the front. Check listings for prices and fitments. Specify whether your car is 1996-97 turbo or c2/c4 1995-98
$151.20
Make a selection 91150332600 This seal sits on the trailing edge of the front fender at the top just below the windshield. It is also used under the back of the rear quarter panel where it meets the side panel. It is also used on the front bumper. We also recommend purchasing the lower seal, part # 91150332500 high-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. View/Change Diagram
From $6.50
Make a selection FVD34101702RAK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrange...(choose a part on the right to read more)
$438.90
Make a selection 115900944020CS Double spring suspension (racing) for 924 only for 20mm spring strut mounting this sport suspension was tuned and tested for racing use only (hockenheimring.net). Perfect handling, recommended for race and clubsport. Not for street use (racing suspension). The lowering is adjustable (30-70mm front and 30-60mm rear). By using springs at the rear axle instead of torsion bars you improve extreme the handling of your car. By removing the rear torsion bars is the weight saving approximately 25kg.
$2,633.40
Make a selection 10050330000 This 9 inch front and 11 inch rear steel fender flare set is made in Germany, we offer a complete line of replacement bodywork to complement the entire Porsche model range. Sold individually. 1 necessary per car. Please note: for conversions, these flares will allow you to run 9 wide tires in the front and 11 wide in the rear. For the 964 / 965 models the torsion bar cut out must be filled. Due to variances in production at the factory, age, accident damage or rust, each part may require trimming and or adjustment for perfect fitment.
$1,648.90
Make a selection 115900997BIT021 The pss 10 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away. Regardless of whether in daily motoring, on the nordschleife of the nurburgring at the weekend, in training courses or in club sports - it's all pure driving enjoyment! Product advantages at a glance: • bilstein mono-tube/inverted technology • bilstein road tested and tuned • high driving dynamics with g...(choose a part on the right to read more)
$4,345.00
Make a selection 115900993BI The bilstein b16 (pss10) suspension kit is the ultimate race inspired suspension system, delivering unsurpassed driving performance in any situation. This suspension kit puts you in complete control, providing the kind of precise suspension tuning formerly available only on race cars. From a weekend of competition to daily driving, this system provides perfect handling performance for every situation. The manually adjustable damping mono-tube gas shock absorbers feature 10-stage precise compression and rebound settings, from comfort to competition. The bilstein b16 (pss10) suspension kit utilizes debris resistant round threads on these dampers to ensure spring adjustment remains effortless throughout the life o...(choose a part on the right to read more)
$4,341.70
Make a selection 240991352GS Pagid yellow rsl 29 are from the rsl line of endurance racing brake pads. They are a medium friction coefficient racing compound with long pad and disc life, and are easily bedded in. Rsl 29 pads are manufactured of a low metallic resin bonded material containing steel and acrylic fibers. They operate in a wide operating temperature range and offer excellent release characteristics. Rsl29 pads offer low heat conductivity and work well with abs systems. They offer excellent modulation and controllability. They offer lower disc wear rates and are fade resistant up to a temperature of 650*c (1,202*f). Applications include: club racing, track days, touring cars, prototype endurance racing and GT cars. Features at a...(choose a part on the right to read more)
$654.50
Make a selection 115900991BI Only for cars without pdcc ( active stabilizer ) bilstein b16 (pss10) suspension kits feature ride height adjustability with 10-stage manually adjustable dampers. Simply adjust compression and rebound settings, from comfort to competition, by rotating the setting number knob at the base of the shock. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Ride height is adjustable from 1.0 to -1.5 20-40mm (front) & -1.0 to -1.5 20-40mm (rear - minimum 1 lowering). Bilstein b16 (pss10) suspension allows you to enjoy the kind of precise suspension tuning formerly available only on race cars. We recommend purchasi...(choose a part on the right to read more)
$4,153.60
Make a selection 115900964BI01 Bilstein b16 (pss10) suspension kits feature ride height adjustability with 10-stage manually adjustable dampers. Simply adjust compression and rebound settings, from comfort to competition, by rotating the setting number knob at the base of the shock. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Ride height is adjustable from 1.0 to -1.5 20-40mm (front) & -1.0 to -1.5 20-40mm (rear - minimum 1 lowering). Bilstein b16 (pss10) suspension allows you to enjoy the kind of precise suspension tuning formerly available only on race cars. We recommend purchasing our lowering collar kit if you plan to run the...(choose a part on the right to read more)
$3,855.50
Make a selection 91151192302EQ This gasket sits on the inside of the hood in the front trunk. It tends to get nicked and cut and will degrade with time. It is essential to keep moisture out of the trunk and should be replaced at the first signs of damage. Sold individually. 1 necessary per car.
$136.40
Make a selection 90150339422 This seal sits on the trailing edge of the front fender at the top just below the windshield. It is also used at the rear fender where it joins the bumper. 4.3 mm in thickness. Sold individually. 4 necessary per car. Driver's or passengers side fitment. View/Change Diagram
From $8.50
Make a selection 90170110600 Finally a solution for the long missing factory id plate from your restored classic Porsche! from our friends in Germany who originally stamped them for the factory come the factory identical originally installed serial number plates for 911 and 912. These plates, identical in every way to the original were often lost when body men repaired these cars, cutting off and replacing the front panels. Over the years these aluminum plates take abuse from paint overspray and oxidation. Totally discontinued by the Porsche factory these are easily engraved with your vehicle identification number. A must for any restored Porsche. General Fitment911 1987-89911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 912 1965-69 911 1965-69
$37.85
Make a selection 91150318601 This seal sits on the trailing edge of the front fender at the cowl just below the windshield. It is also used under the back of the rear quarter panel where it meets the bumper side panel. We also recommend purchasing the left side, part # 91150318501 high-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per car. Please note: this is the thicker width from the SC models. View/Change Diagram
From $6.16
Make a selection 91150332500 This seal sits on the trailing edge of the front fender at the top just below the windshield. It is also used under the back of the rear quarter panel where it meets the side panel. It is also used on the front bumper. We also recommend purchasing the upper seal, part # 91150332600 high-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. View/Change Diagram
From $5.75
Make a selection 91150522100 This seal tends to suffer from dry rot and degrades with time. Be sure to replace it when servicing the bumpers. Any of our OEM replacement parts are designed to appear and perform like the originals. We source these parts in Germany to ensure quality, reliability and precise fitment. When servicing the bumpers, we recommend replacing the shock bushings, part # 91150522100 and base, part # 91150522001 sold individually. 4 necessary per car. 2 front and 2 rear. View/Change Diagram
From $22.95
Make a selection 91150531100 This seal tends to suffer from dry rot and degrades with time. Be sure to replace it before metal on metal contact occurs. Any of our OEM replacement parts are designed to appear and perform like the originals. We source these parts in Germany to ensure quality, reliability and precise fitment. When servicing the bumpers, we recommend replacing the front bumper seal, part # 91150518701 shock bushings, part # 91150522100 and base, part # 91150522001 sold individually. 4 necessary per car. View/Change Diagram
From $6.60
Make a selection 91151192302EQ1 This gasket sits on the inside of the hood in the front trunk. It tends to get nicked and cut and will degrade with time. It is essential to keep moisture out of the trunk and should be replaced at the first signs of damage. This is a high-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
$136.40
Make a selection 240991352RSL1 Pagid yellow rsl1 are from the rsl line of endurance racing brake pads. They are a high friction coefficient racing compound with long pad and disc life, and are easily bedded in. Rsl1 pads are manufactured of a low metallic resin bonded material containing steel and acrylic fibers. They operate in a wide operating temperature range and have good friction stability vs. Temperature. Applications include: GT cars, touring cars, prototype racing and in spring racing. Features at a glance: high friction coefficient high bite high fade resistance high pad and disc life high modulation pagid is one of the leading manufacturers of racing brake pads and is successful at the world's most demanding racetracks. They offe...(choose a part on the right to read more)
$743.60
Make a selection AFC11957 A necessary addition for any 911! This kit includes substitute 30% larger 310 matrix (14"h x 6"w x 2"d) 19 row oil cooler in a factory "hard line" equipped car. This kit is especially good for replacing the factory "loop" oil device located in the front right fender, making it easy to upgrade to a mocal oil radiator at an economical price. Includes the cooler, two 90 degree 3/4 fittings, two 30 mm straight fittings, and a 3/4 oil hose. this is larger than out basic oil cooler kit. Note: for car that already have a factory oil cooler. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89
$475.00
Make a selection 935FSUSP This light weight, bolt in kit replaces the factory front suspension arms, cross-member, and rubber bushings when converting to a coil over front suspension system. General Fitment911 1965-69911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89 914 1970-76
$1,850.00
Make a selection 92862862300 The perfect way to cap off a wiper service. Often times we replace the wipers but let the elements age the cap and wiper arm. We recommend changing your wiper arm and cap at the same time for clean, satin black continuity to your wipers. Sold individually. * please note: please check the model fitment tab to ensure accurate front or rear fitment. View/Change Diagram
From $2.75
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |